Eberspacher HYDRONIC D5W SC 12B (diesel compact)
The pre-launch HYDRONIC D5W SC 12B heater will become for you simply irreplaceable assistant. If you at least once had to warm up in the frosty morning the engine, freezing in salon, you appreciate this device!
Rated voltage — 12 V. Model are suitable for cars, pickups and motor vans with the gasoline engine from 2 to 5 liters. The governing body isn't included in the package of delivery and is acquired separately. The complete set included a mounting kit.
Set of delivery of the heater:
Heater
The fuel pump with a fastening bracket
Water hose 2,2 meters
Bracket for fastening of the heater
The muffler on an entrance of a combustion air
Muffler of exit gases
Muffler pipe 1 meter
Fuel tube of 5 meters
Wiring harness with a block of safety locks
The relay for turning on of the fan of the oven of salon
Package of plugs, fixture, couplers, bolts and nuts, collars, etc. adjusting elements
Structure of the HYDRONIC D5W SC heater.
- An air pump in a combustion tube with a cover
- A combustion tube with a spherical pipe
- Heat exchanger
- Control package
- The circulator (it is built in the heater)
1 Casing
2 An air pump in a combustion tube with a cover
3 A cover of the supercharger – a cover for an air pump in a combustion tube
4 A combustion tube with a spherical pipe
5 Heat exchanger
6 Control package
7 An electric motor cover – a cover for the electric motor
8 The water pump – dismantling of a cover of the heat exchanger with the water pump
12 Consolidation between a casing and an air pump in a combustion tube
13 Mating ring 74 x 3
14 Bayonet an electrode with a cable plait
15 A branch pipe for a bayonet electrode
16 A covering with mating rings for a bayonet electrode
17 Consolidation between a combustion tube with a spherical pipe and the heat exchanger
18 Holder of a branch pipe
19 The plug for a fuel tube from a branch pipe
20 Burning control sensor
21 Cable plait of the sensor
22 The control package plug – the 14-contact plug for the control package (waterproof).
23 Cable plait of the water pump
24 Compression spring
25 A cover of the supercharger – a cover for an air pump in a combustion tube
26 Mating ring 14 x 2,6
27 Mating ring 7,5 x 2
30 Flat head screw of M4 x 10 (1x)
31 Mating ring 5 x 1,5 DIN 37714
32 Taptite M5 x 12 TORX screw (1x)
34 Plug
35 The Taptite M5 x 35 TORX screw (6 for petrol models, 5 – for diesel)
36 The Taptite M5 x 25 TORX screw (2 for petrol models, 3 – for diesel)
37 Cylindrical Taptite M5 x 65 TORX screw (1x)
38 Taptite M5 x 16 TORX screw (1x)
39 Taptite M4 x 10 TORX screw (2x)
40 Countersunk head screw of Taptite M5 x 12 TORX (3x)
in addition only for HYDRONIC D 4 W SC/D 5 W SC
9 The dosing fuel pump
10 Cylindrical filter
11 Holder of the fuel dosing pump
28 Hose
29 A tape for cable mounting
33 Plug
Operation principle of HYDRONIC D5W SC.
At inclusion the indicator bulb in an element of management lights up. The water pump is started. According to the set course of the program the air supply pump in a combustion tube, the heat candle and the dosing pump starting a combustion process is started. At formation of stable process of burning through
certain time bayonet an electrode of incandescence is disconnected.
Depending on the necessary heating temperature change of productivity of the heating device on steps is carried out: HIGH – SMALL – OFF (a regulation pause). At the same time temperature thresholds are rigidly programmed in an electronic control unit. If the need for heating at a step "SMALL" it is so small that temperature of cooling liquid reaches 85 °C, then the heating device passes to a step "OFF". There is an inertial runout within about 120 seconds, then the heating device is switched-off (a regulation pause). The control lamp burns, and the water pump also continues to work during a regulation pause.
| Weight | 8 kg |
Eberspacher HYDRONIC D5W SC 12B (diesel compact) reviews
Be the first to write a review of this product!
